China GB Power Cords: How to Specify CCC, Cable Size, Length and Connector
By CPENT Technical Team · Updated
A China-market power cord is specified in five steps: confirm the product needs CCC, pick the plug by current (2.5 A / 10 A two-pin, 10 A three-pin, or 16 A three-pin), choose the cable from 60227 IEC 52 or 53 by current and length, choose the appliance end (C13, C5, C7 or bare leads), then fix length, colour and packaging. The cable size is not a free choice: it follows the current rating, the cord length and the standard the cord is approved to. CPENT moulds GB 1002 plugs in-house and pairs them with 60227 IEC 52 (RVV) or 60227 IEC 53 (RVV) cable.
Step 1: is CCC needed?
CCC applies to products listed in the compulsory certification catalogue. A cord set sold separately in China is normally in scope; a cord supplied as a component inside a certified appliance may be covered by that appliance's certification instead. Confirm with your certification body which route applies before ordering, and keep the certificate for the exact model.
Step 2: pick the plug by current
| Plug | Current | Typical appliance | CPENT model |
|---|---|---|---|
| GB 1002 two-pin, 2.5 A | 2.5 A | Class II small appliances, chargers | CPT-12 |
| GB 1002 two-pin, 6 A / 10 A | 6–10 A | Class II appliances with higher load | CPT-12A |
| GB 1002 three-pin, 10 A | 10 A | Desktop equipment, monitors, general appliances | CPT-10 / 10Z |
| GB 1002 three-pin, 16 A | 16 A | Air conditioners, water heaters, high-load appliances | CPT-11 |
Step 3: cable size follows current
| Cable | Typical construction | Working voltage | Where it is used |
|---|---|---|---|
| 60227 IEC 52 (RVV) | 2×0.5 / 2×0.75 mm², 3×0.5 / 3×0.75 mm² | 300/300 V | Small appliances, 2.5 A plugs |
| 60227 IEC 53 (RVV) | 2×0.75 / 2×1.0 mm², 3×0.75 / 3×1.0 / 3×1.5 mm², up to 3×2.5 mm² for 16 A | 300/500 V | 10 A and 16 A plugs, general power cords |
The approved combination is what the certificate lists. The rating of a finished cord set is set by its lowest-rated part, so the plug, the connector, the cable and the certificate must all match. A 10 A plug on 3×0.75 mm² is common; for 16 A, confirm the minimum cable size with the test lab, because it depends on the standard, the length and the installation.
Step 4: choose the appliance end
- IEC C13 for most IT and office equipment; C5 for laptop adapters; C7 for Class II audio/video; bare leads with ferrules or tinned ends when the cord is wired inside the appliance.
- The connector must be rated for the same current as the plug. A 16 A plug with a 10 A C13 connector is not a valid 16 A cord set.
Step 5: length, colour, packaging
State the length as the distance from the plug face to the connector face, not the total cable length, and give a tolerance (commonly ±20 mm or ±2%). Say whether the cord is coiled, tied or bagged, and whether the plug needs a cap or a hanger.
What to send for a quote
- Destination: China only, or also export
- Rated current and voltage of the appliance
- Plug standard and appliance end
- Cable type or the current and length, so we can propose the size
- Length with tolerance, colour, printing on the cable
- Quantity per length and packaging requirement
See the AC power cord range or send the specification for a quote with the certificate set for the exact model.
This guide is a buyer summary. Final cable and plug combinations must follow the applicable GB standard and the certificate for the exact model.
Standards & official references
- IEC — International Electrotechnical Commission
- EU Low Voltage Directive 2014/35/EU (EUR-Lex)
- VDE — German electrical engineering association
- UL Solutions — product safety certification
More guides
- Plug Types, Voltage & Frequency by Country
- IEC 60320 Connector Types Explained: C5, C7, C13, C14, C15, C19, C20
- Power Cord Cable Codes Explained: H05VV-F, 60227 IEC 53, SJT, SVT, VCTF
- Micro-Inverter & Solar AC Connectors: C20 vs C28 vs M25 vs Q28
- Which Safety Approval Does a Power Cord Need? Certification by Country
- How to Check a Power Cord Certificate: Model, Scope, Holder, Validity
- Which Connector for Energy Storage and Micro-Inverters? Match the System Position First
- Medical Cable Harness RFQ: What to Send and What a Supplier Can Actually Claim